Carburetor: Quick-Change Vacuum Springs

Time: approximately 30 minutes Tools: small Phillips screwdriver Here’s what you’ll need: Holley quick-change spring housing, vacuum secondary spring kit Tip: During the test and tune process, keep track of which springs help or hinder your carburetor’s performance. They make it easy by color-coding the top of each spring. Here’s what you’ll net: ability to […]

Making Cut-To-Fit Plug Wires, 101

Time: Approximately 2 hours Tools: wire cutters, crimping pliers, razor blade, Sharpie marker What you’ll need: set of quality spark plug wires (boots and terminals included), white dielectric grease, wire socks (recommended), wire looms Tip: When cutting and installing a new set of wires, mark each end at the boots with its designated cylinder number. […]

Hard To Fathom

Mark Hassett #17029371 • Ashtabula, Ohio By Ray Lee • Photography By Pete Sommers In these days of dazzling chrome wheels and flashy paint jobs, Mark Hassett’s Fathom Green 1969 Camaro doesn’t fit the bill. But a true Camaro aficionado will definitely sit up and take notice! This pristine sleeper gives no hint to its […]

Eckler’s New Distribution Center Completed

Eckler’s State-of-the-Art Warehouse/Distribution Center Completed Eckler’s celebrates its $9.5M facility expansion with a grand opening ceremony. City leaders, company executives and many others attended the opening of the automotive leader’s distribution center and warehouse. Titusville, FL December 17, 2014 Eckler Industries, Inc., the nation’s largest provider of restoration parts and accessories for classic and enthusiast […]

The Touring II Reclining Seat Our Exclusive Camaro Option

Today John and our special guest David Alkire discuss our exclusive Camaro seat that reclines the Touring II! Subscribe Today: http://www.youtube.com/subscription_center?add_user=EcklersAutomotive Product Link And Description Below: The Eckler’s Auto Hub is your one stop for all your car restoration needs, we are constantly adding new videos to help you with your installation, feature great products […]

Molding Painting Tips

How to: Removal and refinishing painted moldings Tools you’ll need: Will vary depending on parts. Typically, a screwdriver or socket set will do the trick. Tinware you’ll need: Spray paint, masking tape, fine grits wet sandpaper (800, 1000 grits) Face it. If you drive an old car on a semi-regular basis, you are bound to […]

Refinish Stainless Steel Moldings

Tools you’ll need: besides using a specialty tool to remove the moldings, a power buffing wheel is the only tool needed. Tinware you’ll need: Grits of fine wet sandpaper (600, 800, 1000, 1200, 1500), stainless polish, microfiber towels Any car will greatly benefit from the time invested in precise detail work. However, this is an area that […]

Removal and Replacement of Engine

Tools: standard socket set, standard wrenches, engine hoist, engine stand or cradle, floor jack (if needed) Cost: if renting an engine hoist, expect to pay about $40 for a day’s use Tinware: heavy-duty chain and/or lifting plate Tip: If you pull the motor and trans out together as one unit, invest in a transmission tail […]

Installing a New Intake Manifold

Installing a new intake manifold Tools: standard socket set, standard wrenches, flat-blade and/or Phillips screwdriver, putty knife or scraper, torque wrench Tinware: aftermarket aluminum intake manifold, quality high performance intake gaskets, gasket sealer (silicone) Tip: Before final installation, double check the fit of your parts to make sure everything lines up and will work with […]

Front Lowering Springs and Shocks

Tools: socket wrenches, rubber hammer, pry bar, pickle fork (ball joint removal tool), drill with bit for drilling steel, grease gun, grease. Tinware: front 1-1/2” lowering springs, KYB gas shock absorbers, tie rod ends and polyurethane bushings, upper and lower ball joints, shock mount retainers (if not included with shock kit). Tip: Always support lower […]

Optin Architect